武汉家电维修网 www.whjdw.com 欢迎您的光临!
当前位置: 主页 > 数据调整 > 海尔彩电调整 >

工厂调试项目参数参考表海尔彩电彩电21FA1-TA培训资料

时间:2010-05-16 17:52来源:未知 作者:admin 点击:
D 模式参数调整(8873)_G2
参数名 参数描述 出厂值 初始化值
OSD位置 OSD的起始位置 0E
OPT选项 OPTION,详细说明附后 34
RCUT R CUT OFF 红截止 20
GCUT G CUT OFF 绿截止 20
BCUT B CUT OFF 兰截止 20
GDRV G DRIVE 绿驱动 40
BDRV B DRIVE 兰驱动 40
CNTX SUB CONTRAST MAX 副对比度最大值 7F
BRTC SUB BRIGHT CENTER 副亮度中间值 40
COLC SUB COLOR CENTER FOR NTSC 副彩色中间值(NTSC) 20
TNTC SUB TINT CENTER 副色调中间值 40
COLP SUB COLOR CENTER FOR PAL 副色度中间值(PAL) 02
COLD DVD COLOR CENTER (DIF) 05
SCNT Y-SUB CONTRAST Y信号副对比度 08
CNTC SUB CONTRASRT CENTER 副对比度中间值 3F
CNTN SUB CONTRASRT MINIMUM 副对比度最小值 00
CNTD DVD CONTRAST MAX FE
BRTX SUB BRIGHT MAX 副亮度最大值 20
BRTN SUB BRIGHT MINIMUM 副亮度最小值 20
COLX SUB COLOR MAX 副色度最大值 25
COLN SUB COLOR MINIMUM 副色度最小值 0D
TNTX SUB TINT MAX 副色调最大值 28
TNTN SUB TINT MINIMUM 副色调最小值 28
ST3 SUB SHARP CENTER NTSC3.58 IN TV副画质中间值(NTSC3.58 IN TV) 19
SV3 SUB SHARP CENTER NTSC3.58 IN VIDEO副画质中间值(NTSC3.58 IN VIDEO) 1D
ST4 SUB SHARP CENTER OTHER COLOR SYSTEM IN TV副画质中间值(OTHER COLOR SYSTEM IN TV) 19
SV4 SUB SHARP CENTER OTHER COLOR SYSTEM IN VIDEO副画质中间值(OTHER COLOR SYSTEM IN VIDEO) 1D
SVD SUB SHARP CENTER IN DVD 1B
ASSH ASYMMETRY – SHARPNESS 不对称 05
SHPX SUB SHARPNESS MAX POINTS FROM CENTER VALUE 副画质最大值 1A
SHPN SUB SHARPNESS MIN POINTS FROM CENTER VALUE 副画质最小值 19
TXCX RGB CONTRAST DATA AT MAX DATA OF USER CONTRAST OSD 对比度的最大值
RGCN RGB CONTRAST DATA AT MIN DATA OF USER CONTRAST OSD 对比度的最小值
ABCL ABCL,详细说明附后 15
DCBS DCBS,详细说明附后 95
CLTB The data when TV mode & SOUND SYS = M 详细说明附后 8A
CLTD The data when TV mode & SOUND SYS = M 详细说明附后 89
CLTM The data when TV mode & SOUND SYS = M 详细说明附后 AC
CLVO The data when YVU mode & SOUND SYS != M 详细说明附后 AD
CLVD The data when YVU mode & SOUND SYS = M 详细说明附后 88
OSDA 详细说明附后 01
HPOS 50HZ HORIZONTAL PHASE 50HZ 水平相位(行中心) 13
VP50 50 HZ VERTICAL PHASE 50HZ 场中心 03
HIT 50HZ VERTICAL AMPLITUDE 50HZ 场幅度 1C
HPS SHIFT DAT OF 50/60HZ HORIZONTAL PHASE 行中心偏移量 02
VP60 60HZ VERTICAL PHASE 60HZ 场中心 01
HITS SHIFT DATA OF 50/60 HZ HORIZONTAL PHASE 场中心偏移量 01
VLIN V-LINEARITY 场线性 50Hz 1A
VSC V-S CORRECTION 场S 50Hz 0D
VLIS V-LINEARITY 场线性 60Hz FE
VSS V-S CORRECTION 场S 60Hz 01
UVBLACK 高4位为ublack低4位为&vblack是VCD_0eH的控制数据 88
HBOW HPARA VCD_1BH 中 高3位 和VCD_24H 中高三 位 的数据 88
BRTS SUB BRIGHT 00
RAGC RF AGC ADJUSTMENT RF AGC 调整 2A
HAFC 1/2 AFC DATA ADJUSTMENT AFC调整 86
NOIS 信号强弱界限设定 0F
NDTC NOISE DET count (Weak -> Normal) 1F
VL1 VOLUME OUTPUT DATA AT 25% 09
VL25 VOLUME OUTPUT DATA AT 50% 3D
VL50 VOLUME 100 57
VLX ??? 7F
MUTT Y-MUTE FOR SOFT START 00
STAT CONTRAST UP FOR SOFT START 00
FLG0 Flag0 44
FLG1 Flag1 00
SVM PIC1 SVM 50
VBLK V BLANKING START AND STOP POINT 00
VCEN V CENTERING 17
UCOM 00:GND;01:R OUTPUT;10:B OUTPUT;11:MONITOR RF AGC VIA ADC 00
PYNX Normal H.SYNC max 33
PYNN Normal H.SYNC min 11
PYXS Search H.SYNC max 22
PYNS Search H.SYNC min 1E
RCUTS RCUTS 00
GCUTS GCUTS 00
BCUTS GDRVS 00
GDRVS GDRVS 00
BDRVS BDRVS 00
AV_OPT 详情附后 00
OPT2 详情附后 01
WAIT TIME 开机等待时间 2F
CUR_CEN 拉幕位置 A5
CUR_STEP 拉幕速度 02
AUSTP 04
MODE0 详情附后 09
MODE1 详情附后 0F
OSDF OSD频率 数值越大屏幕上字符越小 60
STBG S TRAP f0 for BG(低4位) 06
STI S TRAP f0 for I(低4位) 08
STDK S TRAP f0 for DK(低4位) 08
STM S TRAP f0 for M(低4位) 08
SSBG
S TRAP HP/LP for BG S TRAP Q for BG S TRAP GD for BG
S TRAP HP/LP for I S TRAP Q for I S TRAP GD for I
S TRAP HP/LP for DK S TRAP Q for DK S TRAP GD for DK
S TRAP HP/LP for M S TRAP Q for M S TRAP GD for M
D5 D4 D3 D2 D1 D0
08
SSI 08
SSDK 08
SSM 09
SYNC 详细说明附后 02
SYBBN 00
SYBBF 00
SYSR 02
BBCT Blue back hysteresis counter (BUS H sync detection 04
VCD0 ???? 00
VCD1 D1D0:00 38M;01:38.9M?????? 00
BL25 % of ATT for Balance 25 1E
BL49 % of ATT for Balance 49 50
OV50 OSD vertical position for 50Hz 0C
OV60 OSD vertical position for 60Hz 02
HIT1 16.:9调整范围 04
HIT2 放大图像调整 04
COLX2 3A优化开时色彩调整 05
PCON 连续按0键 图像所恢复的对比度数值 32
PBRI 连续按0键 图像所恢复的亮度数值 32
PCOL 连续按0键 图像所恢复的彩色数值 32
PTIN 连续按0键 图像所恢复的色调数值 32
PSHA 连续按0键 图像所恢复的清晰度数值 32
PVOL 32
BR_BRI 亮时亮度数值 50
CO_BRI 一般时亮度数值 32
DK_BRI 暗时亮度数值 32
BK_BRI 漆黑时亮度数值 1E
BR_CONT 亮时对比度数值 64
CO_CON 一般时对比度数值 64
DK_CONT 暗时对比度数值 32
BK_CON 漆黑时对比度数值 32
V_NOISE 声音 吵时数值 28
V_MID 一般 1E
V_QUIET 0F
PWR
BUS
MEM
Q501
QT01


OPT:
BIT FUNCTION
0 Hotel mode 1:欢迎光临 logo 0:海尔 logo
1 No use
2 V_Mute ON/OFF when CH changes(=1:ON)
3 AUDIO GAIN SW of tb1240
4 Not VT Down of AFT when No Signal(=1)
5 TINT 0:use 1:unused
6 Select TV sync(0) or MONITOR sync(1)
7 Mute of av switch key 1.use 0.no use

ABCL:
BIT FUNCTION
0 ABL-Gain 00:-0.2;01:-0.4;10:-0.6;11:-0.8v
1
2 ABL Start Point 00:-0.0;01:-0.15;10:-0.3;11:-0.45v
3
4 ACL ST ????????
5
6 WPS 0:Y peak limiter off 1:Y peak limiter on,105IRE
7 No use

DCBS?
BIT FUNCTION
0 BLACK STRETCH 黑电平延伸 00:Off;01:Black stretch point,26IRE; 10 : 33 IRE; 11 : 43 IRE ???
1
2 Y GAMMA 00:Off;01:Y γ point 90 IRE,Gain –3dB; 10 : 82 IRE ; 11 : 75 IRE
3
4 VCD BS SW
5 VCD CORING
6 VCD BLACK
7 C TRAP Q

CLTB\CLTDCLTO\CLTM\CLVO\CLVD
BIT FUNCTION
0 Y Delay Time 000:-40 nsec;001:0;010:40 nsec;011:80 nsec;100:120 nsec;101:160 nsec;110:200 nsec; 111:240 nsec
1
2
3 N Phase 00:USA(105 degree);01:Japan(93 degree);10:11:DVD
4
5 Color Y 0:Color gamma off ;1:On;
6 PN-ID Sens 0:PAL/NTSC killer sensitivity,1mVpp; 1:10mVpp
7 FID 0:Normal;1:Alwas killer off,i.e. always color on..

SYNC:
BIT FUNCTION
0 Select sync slice level for weak signal
1 Select sync separation level
2 Select H sync judgement : 0:BUS, 1:TC3
3 UNUSE
4 UNUSE
5 UNUSE
6 UNUSE
7 UNUSE

SYBBN:
BIT FUNCTION
0 UNUSE
1 UNUSE
2 Select window pulse for H lock detection
3 Select H lock detection mode
4 Select SY-DET-1 for sync dtection
5 Select SY-DET-2 for sync dtection
6 Select LPF mode for sync dtection
7 UNUSE


SYBBF
BIT FUNCTION
0 UNUSE
1 UNUSE
2 Select window pulse for H lock detection
3 Select H lock detection mode
4 Select SY-DET-1 for sync dtection
5 Select SY-DET-2 for sync dtection
6 Select LPF mode for sync dtection
7 UNUSE
SYSR:
BIT FUNCTION
0 UNUSE
1 UNUSE
2 Select window pulse for H lock detection
3 Select H lock detection mode
4 Select SY-DET-1 for sync dtection
5 Select SY-DET-2 for sync dtection
6 Select LPF mode for sync dtection
7 UNUSE
FLG0:
BIT FUNCTION
0 0:NORMAL;1:PIF over modulation switch on
1 0:BPF;1:TOF
2 0:Nyquist Buzz cancel,on;2:off
3 0:Off, 1:If BB=1, RGB out is 110 IRE
4 TB1254N band pass filter switch
5 SIF FIX Select 0:fix to normal, 1:control with sound system
6 SIF 5.74 Select In D mode, aplly this bit to SIF 574
7 vco readjust when position select 0:disable;1:enable;
FLG1:
BIT FUNCTION
0 CW SW
1 V ramp bias
2 Sync. Sepa. level
3 Horizontal side blanking
4 UNSED
5 UNSED
6 1:计时收看清到20H;0:计时收看清到0H
7 1:用户可按SLEEP键清除收看计时;0:不可
SVM:
BIT FUNCTION
0 SVM gain 00:-6dB;01:0dB;10:+6dB;11:+12dB
1
2 SVM DL(svm delay) 00:off;01:-100ns;10:-60ns;11:-40ns
3
4 Mon、svm ??????
5
6 1:有软换台0:无
7 UNUSE


VBLK
BIT FUNCTION
0 00:23H;01:33H;10:37H;11:41H (50Hz) 00:22H;01:30H;10:34H;11:38H (60Hz)
1
2 00:310H;01:299H;10:295H;11:291H (50Hz) 00:263H;01:254H;10:250H;11:246H (60Hz)
3
4
5
MODE0:
BIT FUNCTION
0 1:218频道;0:100频道
1 1:5060 (M制);0:两路AV (无M制时,几路AV用AV option来控制 )
2 0:有SECAM制;1:无
3 1:RGB Out-Cut Off DC;0:Y-MUTE
4 1:有些屏显一直显示;0:有些屏显有时显示
5 0:ALPS 1:北松
6 SHOP OUT 00:DK;01:I;10:BG
7
MODE1:
BIT FUNCTION
0 0:无BG;1:有
1 0:无I;1:有
2 0:无DK;1:有
3 0:无M;1:有
4 0:when asm & search,set up VCO adjust req. ,1:only power on 0:PIF VCO adjust trigger 1: normal (12 :bit 7)
5 The algorithm of ASM. 0:ASM doesn't judge IFLOCK with case 4. 1:ASM judge IF LOCK with case 4
6 The algorithm of ASM. 0:ASM doesn't judge Fhsync with case 4. 1:ASM judge Fhsync with case 4
7 TINT polarity ,input to V/C/D. 0:normal 1:invert
AV_OPT:
Byte FUNCTION
Video1 Video2 Video3
0 VIDEO DVD
1 VIDEO S-VIDEO DVD
2 VIDEO DVD VIDEO
3 VIDEO S-VIDEO DVD
4 VIDEO/S-VIDEO DVD
5 VIDEO/S-VIDEO VIDEO DVD
6 VIDEO DVD VIDEO
7 VIDEO VIDEO DVD
OPT2:
BIT FUNCTION
0 lunar calendar 1:have lunar calendar ; 0:no lunar calendar
1 No use
2 1:只有英文 0:有中文
3 AV是否静噪;1:静噪;0:不
4 No use
5 1:有超强接收功能0:无
6 No use
7 0:有开机欢迎语1:无
BIT FUNCTION
0 akb CUTOFF SENSITI VITY 00:*9.75;01:*10.00;10:*10.25;11:*10.50
1
2
3 MOD.3:0 CUTOFF range:-0.65~+0.65;1:-0.65~+0.85
4 000:无;001:45.75;011:38.9;100:38.0
5
6
7
------分隔线----------------------------